Hisaint for HP 680 Ink Cartridge Apply To 3638 1115 1118 3636 2135 2138 3635 | Компьютеры и офис

Hisaint for HP 680 Ink Cartridge Apply To 3638 1115 1118 3636 2135 2138 3635 | Компьютеры и офис

Each batch of the board may be different, but does not affect the use.
Please according to the model of the original ink cartridge to purchase (previously used cartridge model) , don't directly according to the printer model,the same printer model, different regions may use different cartridge model.If you need help, please contact customer service.Thank you.

 installation instructions:                                                                        

To tear cartridge nozzle to the Trailer 1 cartridges before.

2 replace the new ink cartridge, cleaning the print head before the ink cartridge is used up.

3 after installing the cartridge, let the cartridge in the cartridge box for 5 minutes. Clean the print head until the nozzle check is normal.

4 if there is a break or lack of color, so that the ink cartridge in the cartridge to stay within 10-15 minutes.

5 if the printing problem still exists, follow the printer to use the manual to detect the print head 1-3 times until the print patency.

6 if the printer does not recognize the cartridge, please remove the cartridge to re install, if the printer is still not working to try to restart the printer.

7 after the Kaifeng ink cartridge, please run out in 6 months to ensure the best printing effect.

8 please don't take out the ink box from the printer before you use it.

9 printer at least once a week, to prevent the head of the printing head

Three: replace the ink cartridge:

When replacing the cartridge must follow the steps in the operation manual. The measurement of ink capacity by the printer is to use the electronic counter inside the printer.

In the process of replacing the ink box, the printer will reset its internal electronic counter so as to confirm that the new ink box is installed.

Please note the following points to replace the cartridge:

1, can not use the hand to touch the ink box outlet, in order to prevent the impurity into the ink box;

2, do not fall into the ink box, to prevent leakage of ink.

3, the ink is conductive, if the leakage of the circuit board should be used without water ethanol wipe, cool dry after re energized, otherwise it is possible to damage the circuit components;

4, the ink box should be kept in a clean room, save the temperature should be between +35;

5, external ink cartridges can not be raised, can not be reduced.

Four, maintenance instructions:

I love your printer, go to the regular maintenance center to do regular maintenance for your printer.

I don't like long time printer, please open the printer regularly, according to the cleaning key cleaning nozzle.

] If problems affecting the quality of printing ink, can be returned free of charge, the cartridges in the market sales and use, a year to feedback information statistics returned rate is less than 1% of that brand excellent, stable quality, please rest assured that use.

In the above problems encountered during the printing process, should first conduct self missing line patterns, should clean the print head. Under normal circumstances, through the washing of the print head and then self inspection, the pattern has no line phenomenon.

- if after cleaning, self check design still lack a line phenomenon, please repeat 2-3 times. Under normal circumstances, the pattern of the line will be reduced, which proves effective cleaning, should adhere to the cleaning.

Exergy continuous cleaning are still unable to meet normal print, ink in the ink has little or no need to replace the cartridge.

Install new fusulinid cartridges, sometimes encounter self missing line or a certain color spray can not. At this time, do not easily judge to print head clogging, mostly due to transit jolt and inverted storage and other reasons cause should be cleaning the print head.

Exergy under normal circumstances, if there is self check design small short line, if not beat high quality images (just to play the file), normal print, without cleaning the print head.

Five, ink cartridges use common sense:

1 the storage of the ink box will be placed in room temperature environment, to avoid the sun, strong light and heat storage. Not in the cartridge machine installation is used, do not tear apart the packaging and air hole seal cartridge. In after unpacking the cartridge, as soon as possible should be installed on the printer, otherwise it may cause ink ink box leakage or gush out color. In order to achieve the best printing effect, please use the cartridge in the six months after the end of the use of.

2. The cartridge mounting and replacement when printing process, run out of ink (ink out) display lights start flashing, ink will have been exhausted, at this time can still be continuous and print the number of sheets until the display lamp stops flashing, at this time should immediately replace the print cartridge.

When installing the ink cartridges must be in accordance with the guidelines on the printer specification tore off the air hole seal, but not free to tear to the bottom of the ink cartridge tape or ink leakage. Each time you install a new cartridge, the general need to clean the printer head 2-3 times. The printer is not working, even if there is no ink or no ink in the cartridge. Once the new ink cartridge falls, it is not desirable to replace the front. Unless you want to replace the cartridge, usually do not open the cartridge protection clip, otherwise the cartridge may not be able to use.

Six, printer maintenance:

- in order to keep your printer in the best working condition, within one year should be thoroughly washed several times.

Turn off the power - clean, remove all paper from the feeder, with a wet wipe.

- improper handling will cause serious damage to the printer, when handling must be properly packed (it is best to use the original packaging).

Exergy before transporting the printer should be to ensure that the print head is hooded, and the cartridge homing, never cartridges away from inside the printer.

- keep the printer flat, in the process of handling not inverted, or print head cleaning slot in the ink will be back out

Seven, print head maintenance:

Most expensive parts - the print head of the inkjet printer, but it is not as you think so easy to plug, plug the print head of the general, can solved by cleaning the print head.

The key to maintain the print head - is the correct operation of the printer and high-quality ink cartridge.

In general the service life of the print head to replace 20 to 30 sets of cartridges.

The print head to print the file - service life than a large number of printing color halftone or gray graphics for long time.

- when the black or colored ink (INK OUT) can not clean the print head or flashing light, it should replace the cartridge.

Printer must be kept in the installation has plenty of ink cartridges, long time does not use printer is extremely easy to cause the plug the print head, so must guarantee within a week at least once, otherwise the print head is probably blocked by the ink dry.

- to do not often use the printer, in a print head cleaning before shutdown.

The working principle of exergy of Epson inkjet printers with Canon, HP different, it adopts multi-layer head technology, make the ejected ink were round, when the ink from the nozzle is not the formation of fog, so can make clear printing effect, especially photo series more applicable to print pictures. However, due to the structure of the printer is different, CANON more easily into the air than the EPSON, it is easier to plug the head.

Eight, check and solve the bad when printing:

When printing line appears white or light color, graphics, color, blurred or print out.

1 ink tube into the air or the print head with impurities to start the automatic cleaning process of the printer to clean the print head 1 to several times

Note: the end of each cleaning process must print the nozzle check pattern test line to observe the cleaning effect, or close the printer to stop using a few hours to see if it has improved.

2. Follow the instructions to tear to yellow seal or seal not clean tear and an air guiding groove, an air guide hole is still in the closed state, air can not enter the cartridges.

Solution: the seal can be completely torn off

3 such as the above reasons have been ruled out, after the replacement of the new cartridge is still not print out the estimated nozzle has been burned or motherboard problem, it is recommended to send authorized maintenance center to check.

4. Print nozzle blocking: print head did not return to in the protective cover or unexpected fashion into new cartridges, resulting in the print head in the air exposure for too long and dry blocking. Pay attention to print to ensure that the print head back to the protective cover, and replace the cartridge should be replaced as soon as possible. Can start the cleaning process.

5 without long-term attention to boot, electricity and cleaning spray nozzle, so as not to dry and blocking

Don't print work will hand into the printer or touch the cartridge. When you have doubts about the quality of the ink cartridge, and from the printer to remove unused cartridge, please with transparent tape sealed at the bottom of the ink ejection port and with a sealed plastic bag, turn to your purchase of dealers, for production testing and to determine the quality of the cartridge.